Installing 2nd gen Coil springs (cont)

Drivers side finished.

Installing 2nd gen Coil springs (cont)

Passenger side, finished

Installing 2nd gen Coil springs (cont)

Where the end of this pry bar is is where some "Persuasion" has to be done. We had to lift up on the edge of the coil spring with the pry bar (as shown) and get the end of the coil over the lip so it would sit in the lower control arm spring pocket. As mentioned it takes persuasion. Whereas getting the spring to fall into the pocket required loosening the spring compressor and then installing the spindle, you might have to loosen or tighten the coil spring compressor up for this operation enough to get it over this lip. Not an easy task. BE CAREFUL.

Installing 2nd gen Coil springs (cont)

Crank down and compress the spring. You should compress it until you can fit the spring into the pocket of the lower control arm. This does take a little force. We had the spindle attached to the lower control arm, pushed the spring forward into the pocket, then attached the spindle to the upper control arm ball joint.

Installing 2nd gen Coil springs (cont)

This is how it looks from the underside. Try to hook the hooks as close to the end of the threaded shaft fairly close to the end of the shaft with only a small amount thread coming through. This allows a lot of compression to be made.

Installing 2nd gen Coil springs

Using the Autozone kit, kit#27035 you can install the coil springs just like the tool that GM used to do this with. The long shaft goes through the opening in the top of spring pocket. This shaft is just large enough to sit in this hole. We used a washer in between the frame and bolt head.
Here is the link and a picture to the kit.
http://www.autozone.com/autozone/accessories/OEM-Coil-spring-compressor/_/N-264t?counter=0&filterByKeyWord=coil+spring+compressor&fromString=search&itemIdentifier=555573_0_0_

How to Install coil springs

This is how Corbin and I felt after trying to install the coil springs initially with the coil spring compressor. It was the right compressor, just the wrong technique...

AS ALWAYS, FOLLOW THE INSTRUCTIONS PER YOUR INSTRUCTIONS THAT COME WITH THE COMPRESSOR AND BE AWARE OF THE POTENTIAL HAZARDS. COIL SPRINGS ARE VERY DANGEROUS. I AM NOT A CERFTIFIED MECHANIC AND THIS IS NOT A TECHNICAL BULLETIN OR AUTOMOTIVE MANUAL- FOR REFERENCE ONLY.
JOEL

Upper and lower controls arns installed

Upper controls arms were not a big deal. The lowers on the other hand were no easy chore. I had to grind off some on the ends of the bushings due to the distortion in the subframe where they were.

Springs painted and ready for installation, 1 full coil cut off

Picture of the Spring after rust removal by electrolysis

Simply, the charge breaks down the bond between the Iron and Oxygen (iron oxide= rust). You are left with a very nice surface that is prepped for bonding (less cleanup).

Electrolysis

The springs are all painted and ready for install. I used electolysis to remove the rust from them because blasting was wearing me out. Yes, my nerd side coming through.

Upper and lower control arms are painted (bushings installed- Thanks TK)

Not correct (would have been bare metal half way up the arm and the rest as well) but I think it turned out OK. A little bit of sandblasting goes a long way.

Clutch pedal and the harness. Well harness almost in.

Dash in

Dash is in, steering wheel is in. I used the Krylon Fusion in Semi gloss to paint the column. It turned out very nice. Great to see it looking like a car again!

Taillights are in! I cleaned them up and had to buy a new rear taillight harness. The base bird lights and trans am harness does not interchange- more learning curve things.

Heres another shot of the tank. I put the exhaust in before the tank went in to keep it easy. I had to drop the axle to get the exhaust in- easily...

Got the gas tank painted and reinstalled. I used some rubber strips under the straps. Turned out pretty nice. That is the Rustoleum aluminum color paint, high temperature version. Turned out pretty nice. It looks good with some color under there.